Computer - GHOST parameters and displaysGhost | Programing Reference For .Net,Java,C

GHOST parameters and displays

GHOST introduced in all parameters can be set in the parameters of options
1. Image write buffering: in the establishment of backup documents, opened write buffer;
2. Sure: this option, there will no longer be asked to confirm the final (not recommended this option);
3. No int 13: The choice, do not support interrupt 13 (not default choice);
4. Reboot: in the area of the hard disk or operation is complete, restart the computer automatically;
5. Spanning: Vol framework through multiple backup file (this option, write buffering closed);
6. Autoname: automatic file naming for spanning;
7. Allow 64k fat clusters: only support Windows NT;
8. Ignore CRC errors: ignore CRC error;
9. Override size limit: If a district does not match the size, can be neglected implementation;
10. Image read buffering: Open generation backup cache read documents (selected the default).

Ghost other parameters on
1.-rb end of this operation from Ghost automatically restart. Thus, in the reproduction system we will be able to leave.
2.-fx end of this operation from Ghost automatically return to the DOS prompt.
3.-sure to confirm all the requirements tips or warnings are answered, "Yes." The parameters of a certain risk, only recommended for advanced users.
4.-fro that bad if the source of cluster zoning, skip mandatory tips copy. This parameter can be used to try to save the data in the hard drive bad sectors.
5. @ Filename in the filename specified in the txt file. Txt file for the Ghost of additional parameters, it can be exempted from DOS command line 150 characters restrictions.
6.-f32 source FAT16 district will be converted to FAT32 after copy (prerequisite is the target area of not less than 2 G). WinNT 4 and Windows95, 97 users cautiously uses.
7.-bootcd directly to the CD-ROM when the backup file, this option can make a bootable CD-ROM. Add to this process needs startup disk.
8.-fatlimit NT will be the FAT16 zoning restrictions in the G 2. Copy this parameter in Windows NT district, and do not want to use 64 k / Cluster FAT16, very useful.
9.-span-volume parameters. When the lack of space at the tips copied to another area of another backup package.
10.-auto-volume copy does not automatically give tips on continued implementation of a file name.
11.-crcignore neglected backup in the packet CRC ERROR. Unless the needs of the rescue package of data backup, or do not use this parameter to prevent data errors.
12.-ia all image. Ghost will drive all the district-by-backup.
13.-ial all image, similar to - ia parameters, the Linux partitions each backup.
14.-id full image. Similar to - ia parameters, but contains information to guide district.
15.-quiet operation in the process of updating and user prohibit state intervention.
16.-s cript can execute multiple Ghost command line. Command line deposited in the designated document.
17.-span opening of the inter-volume document imaging functions.
18.-split = x backup packages will be sub-divided into a number of volumes, each volume the size of the x Katherine. This feature is very useful for large-scale backup packages copied to the mobile storage device, such as a 1.9 G backup copy to the three-disc recorder.
19.-z disk or partition to preserve the contents of a document image compression. - Z or - z1 lower compression ratio (Rapid) - z2 for high compression rate (velocity) - z3 to - z9 compression rate were increased (followed by slow speed).
20.-clone Ghost realize this is no backup / restore core parameters.
The use of grammar: - clone, MODE = (operation), SRC = (source), DST = (destination), [SZE (size), SZE (size )……]
This trip is more complex parameters, and the parameters can not contain spaces.
Intended for operation of these types of operations, the value of desirable: copy: disk-to-disk; load: document to disk; dump: disk to a file; pcopy: district to district; pload: documents to the district; pdump: Outline the document. Source intended for the operation source of desirable: drive, from the beginning of the file name or for the need to write absolute path. Destination intended target location, value desirable: drive, from the beginning of the file name or for the need to write absolute path; @ CDx, recorders, x burners that drive, from the beginning.

Below illustrate:
Command-line parameters: ghostpe.exe-clone, copy mode =, src = 1, dst = 2
Completed operations: local disk to a local copy disk 2.

Command-line parameters: ghostpe.exe-clone, mode = pcopy, src = 1:2, 2:1 dst =
Complete the operation: a local disk on the second District 2 copied to the local disk of the first district.

Command-line parameters: ghostpe.exe-clone, mode = load, src = g: \ 3prtdisk.gho, dst = 1, sze1 = 450M, sze2 = 1599M, 2047M = sze3
Completed: From a disk loading image files, and the first district adjusted to the size of 450 MB, and the second adjustment for 1599 MB, and the third adjusted to 2047 MB.

Command-line parameters: ghostpe.exe-clone, mode = pdump, src2: 1:4:6, dst = d: \ prt246.gho
Complete the operation: the creation of the district only with selected image files. Choose from disk 2 District 1, 4, 6. Understanding of these parameters, we can easily achieve Ghost unmanned backup / copy / resumed. Chong coffee.

Notes
1. Backup system, a single backup paper it is best not more than 2 GB.
2. Backup system, it would be better to delete some useless paper documents in order to reduce the volume of Ghost. Usually useless files: Windows temporary folder, IE temporary folder, Windows memory swap files. These documents are usually accounted for over 100 trillion hard disk space.
3. Backup system before finishing goals set and source disk to speed up the backup speed.
4. Backup system and restore the former system, the best check the source and target was set to rectify the wrong disk.
5. Recovery systems, it is best to first check whether the recovery goals set an important document not transfer, should not be covered, such as hard drives, and only regret ah.
6. Choice compression rate, is not recommended opted for the highest compression rate, the highest compression rate because very time-consuming, and compression ratio has not been significantly improved.
7. Installation of the new software and hardware, the best produced a new image files, or are likely to resume after some inexplicable mistakes.

Ghost list of command line parameters
As follows:
/? Or / H: Show help.
- CLONE: cloning.
- IA: for all sectors in the district for mapping.
- ID: the entire disk (not including the Space Division) replication.
- IR: ID and the same, but will not adjust district boundaries for the sector.
- IB: Copy only the start-up disk sector.
- IAL: LINUX partition of the entire replication, the district will use other methods to normal.
- OR: covering space and the integrity check.
- NOLILO: Do not try to duplicate that LILO start of the redeployment.
- BOOTCD: When using - SURE direct production of CD-R mapping, expect to find boot floppy.
- FDSZ: removal of the signs on the disk goal of bytes.
- FDSP: reservations targets on the disk symbol of bytes. (Priority over - FSSZ)
- LPM: LPT parallel connecting the main mode.
- LPS: LPT parallel connector from the model.
- TCPM: TCP / IP host connector model.
- TCPS: TCP / IP connectivity from the model.
- USBM: automatic entry into the USB host mode.
- USBS: automatic access from the USB model.
- JL: Record multicast session diagnostic messages to a file.
- JS: set the maximum value of multicast.
- JA: Setting up a multicast session name.
- AUTO: Do not prompted, enter the file name, the use of default values.
- CHKIMG: Check the integrity of the document image.
- PWD: designated password.
- SKIP: Skip the specified needs of the FAT file system file or directory.
- PMBR: When any disk copying operations, the retention goals disk master boot record.
- SPAN: Allow access to a number of volumes.
- SPLIT: When creating mappings will be divided into several blocks mappings.
- Z: Mappings document.
- F64: When transferred to the old mapping documents to allow 64 K cluster size.
- FATLIMIT: FAT district size to prevent more than 2 trillion.
- F32: FAT16 will be converted to FAT32.
- NTD: Allow NTFS internal diagnostic tests.
- NTC-: for the Prohibition of NTFS cluster distribution.
- NTCHKDSK: mandatory NTFS Volume CHKDSK next start.
- NTIC: ignore NTFS Volume on the CHKDSK bit.
- NTIL: ignore non-empty NTFS inspection of the log file.
- NTIID: ignore zoning system identifier replication.
- TAPEBUFFERED: the default mode tape.
- TAPESAFE: When using the old or unreliable tape when useful.
- TAPESPEED: Allow home-tape speed.
- TAPEUNBUFFERED: non-mandatory tape input and output buffer.
- TAPEEJECT: mandatory after the pop-up tape operation.
- TAPEBSIZE: tape block size.
- RB: after the completion of compulsory reproduction automatically restart.
- FX: Upon the completion of a duplicate withdraw from the process.
- QUIET: quiet mode.
- SURE: and - CLONE options used together to avoid questions.
- BATCH: batch mode, and all operating procedures by automatically completed.
- NOFILE: Ban paper asked.
- SCRIPT: Automatic according to the script file in order to run a program.
- DL: designation of the drive.
- FIS: Use of a maximum hard drive.
- FNX: Ban extended support on the 13th interruption.
- FFX: Use extension on the 13th interruption.
- FNI: ban on direct access IDE hard drive support.
- FFI: Use direct IDE hard disk access.
- FNS: ban on direct ASPI / SCSI hard disk access support.
- FFS: Use direct ASPI / SCSI hard disk access.
- NOSCSI: Prohibition of the Use ASPI access SCSI devices.
- BFC: dealing with bad FAT cluster.
- VDM: use of the use of written orders to check disk check every sector on the disk.
- FRO: mandatory even if there are bad cluster also continue to reproduce.
- CRC32: Use CRC32 check.
- CRCIGNORE: try to ignore the mistakes in the mapping file.
- FCR: When the establishment of documents created when checking documents.
- AFILE: the suspension of the use of specified documentation.
- DI: Showing diagnosis.
- MEMCHECK: Diagnosis memory.
- DD: Record-disk information to GHSTSTAT.TXT
- DFILE: the use of the designated information log files.
- FINGER: Display detailed fingerprint information.
- VER: display program version.

1.-rb end of this operation from Ghost automatically restart. Thus, in the reproduction system we will be able to leave.
2.-fx end of this operation from Ghost automatically return to the DOS prompt.